Aspen Plumbing and Rooter

How to Stop Tree Roots in Sewer Line from Wreaking Havoc

Fri, 27 Sep 2019 19:39:00 GMT

As a homeowner or business owner, there’s a lot on your plate when it comes to maintaining the building. You never know when a problem could arise, and that’s why it’s so important to keep things under control at all times. One problem that’s more common than you think is tree roots in sewer line […] The post How to Stop Tree Roots in Sewer Line from Wreaking Havoc appeared first on Aspen Plumbing and Rooter.

When the roots invade the sewer lines, extensive and costly damage can occur. And once this damage occurs, it could turn into a big mess to clean up. To prevent this from happening, know how to stop tree roots from growing into your sewer lines and causing havoc.

To learn everything you need to know about preventing this catastrophe, continue reading below!

How It Happens

So, why do tree roots grow into sewer lines and how does it happen?

Because sewer lines contain moisture, they attract the tree roots . This is the beginning stages of the invasion process. During this stage, it might be hard to detect a problem.

As they nourish themselves off of the moisture, the roots begin to grow and get thicker. Once the roots become thick and strong, the pipes begin to weaken. Tree roots can wrap around pipes causing them to bend and crack, or they can break right through the pipe and begin to grow inside the pipeline.

At this point, the only way to fix the problem is to call in the professionals. Professional plumbers will know how to remove the tree roots with creating as little damage to your sewer lines as possible.

Know the Signs

There are several ways to detect tree root growth in your sewer lines. You should be on the lookout for problems with your plumbing including gurgling in the toilets or the drains draining slowly. If there are trees located near your sewer lines, then you should have your lines inspected to determine if roots have invaded them.

Signs that your sewer line has broken include a musky odor and dips in your lawn. The smell is due to the fact that your sewer lines contain sewage and when it breaks, you smell the continents. If the line breaks, water is most likely leaking out.

When the water leaks out, the soil around the line gets wet and the soil gives away, creating the dip in your lawn. If you notice any of these problems, then it’s a good idea to check your sewer lines for tree roots!

How to Prevent It

Unfortunately, you don’t have control over mother nature. You can’t stop tree roots from growing in specific directions (towards your sewer lines). You can remove all trees from your property, but trees on public property or trees in your neighbors’ yards can still grow onto your property and into your pipes.

Here are several ways to prevent tree roots from growing into your sewer lines as best as possible.

Barriers

There are both chemical and physical barriers made specifically for preventing roots from growing into your sewer lines. The chemicals made for this purpose contain copper sulfate and potassium hydroxide. The chemicals release slowly and are a common form of prevention with many commercial buildings.

Spread these chemicals around the pipes and tree roots will stay clear of the area. You can also consider using materials such as woods and metals to protect your sewer lines from the roots. This prevention tactic might take a bit more effort, though.

Heavy-Duty Pipes

There are heavy-duty pipes available for you to install. If your home or business is located in an area where there is an abundance of trees, then replacing your old pipes with heavy-duty pipes could save you money down the road. Heavy cast iron pipes are some of the best pipes to use for preventing tree root growth.

The smallest crack in your sewer line could cause a frenzy with tree roots. Using heavy-duty pipes means less chance of cracks occurring and more combat against the roots.

Sewer-Safe Trees

A tree-less yard or business isn’t always the only answer you have. If you enjoy trees in your yard, but don’t want the hassle of their roots invading your sewer lines, then take great consideration in what type of trees you plant and where you plant them.

If the tree you’d like to plant is a large tree that’ll grow quickly, then consider planting it as far away from the sewer lines as possible. If you’d like to plant multiple trees, be sure that they’re smaller trees with small root balls.

The most important thing to remember is that you want trees that have shallow root structures. These kinds of trees are less likely to grow into your sewer lines and cause problems.

Do You Have Roots in Sewer Line Pipes on Your Property?

Now that you know how tree roots grow into your sewer lines and why, it’s time to ensure that your sewer lines are tree root free. Do you have roots in sewer line pipes on your property? Take the time to look for the signs of a broken pipe.

If you’re noticing some of these signs, then call in the professionals to do a full inspection of your sewer lines. This is the best way to ensure that your sewer lines are kept clear and functioning properly.

Contact us today to request a free quote on our plumbing services! And once you fix the problem, or before the problem arises, be sure to follow our prevention tips!

The post How to Stop Tree Roots in Sewer Line from Wreaking Havoc appeared first on Aspen Plumbing and Rooter .

Help! I Have No Hot Water!

Fri, 27 Sep 2019 19:37:00 GMT

Imagine the scene: you’re ready to start your day and you hop in the shower, and suddenly nothing but ice-cold water is coming out. It’s an all-too-common problem with homeowners when they discover they have no hot water to do the things they need to. If you’ve discovered you have no hot water, there’s no need to […] The post Help! I Have No Hot Water! appeared first on Aspen Plumbing and Rooter.

Imagine the scene: you’re ready to start your day and you hop in the shower, and suddenly nothing but ice-cold water is coming out.

It’s an all-too-common problem with homeowners when they discover they have no hot water to do the things they need to.

If you’ve discovered you have no hot water, there’s no need to panic. Check out this helpful guide that explores a few reasons why you’re out of hot water and what you can do about it.

Your Gas Water Heater’s Pilot Light is Out

If you have a gas water heater in your home, there could be a few reasons why you suddenly have no hot water. First, make sure your water heater is getting the gas it needs.

Every once in a while, the gas supply can turn off or it could be interrupted. You’ll need to turn the gas control knob to PILOT and remove the cover where the burner and pilot light are located.

Once you find the location of the pilot light , look for a flame. If you don’t see one, it could be that the pilot light has simply gone out.

To reignite your pilot light, turn the regulator to the off position and then wait around five minutes for all the gas to safely disperse. Next, turn your regulator to pilot mode.

For heaters with the self-ignite feature, just hold down the ignition button for around a minute, then turn the regulator back to on. If you have to use a flame, use a long grill lighter and direct it right at the pilot burner. This should cause the pilot light to reignite.

If you’re still having issues, it may be related to the water heater’s thermocouple unit. This is an inexpensive part, and some gas companies will even come and replace it for free, so it can’t hurt to ask.

Thermostat Issues

Your water heater should have a thermostat that allows you to regulate the water temperature. Ideally, this temperature should be set between 122 and 140 degrees.

If you notice that it’s lower than these numbers, simply turn the temperature up and see if the hot water resumes. Anything operating below the average range can not only be annoying, but it may also put you at risk for the growth of bacteria in your water.

When the water temperature is too low, it can increase the risk of Legionnaire’s disease, so pay close attention to the thermostat readings. Wait around 30 to 40 minutes after you turn it up, and you should have hot water again.

No Hot Water? It Could be Due to Sediment Buildup

As time goes on, your water heater can accumulate a range of sediment and other contaminants. When the water heater deals with sediment buildup, it can harden inside the bottom and reduce the ability to produce hot water.

To fix this problem, you should clean out your water heater on a regular basis. A water softening agent can also help to reduce the amount of buildup inside the unit.

You’ll need to completely drain the water heater before you can remove any sediment. Flush the unit using clean water and some vinegar to help get rid of stubborn limescale and other debris.

A regular flush of your water heater can help to improve not only the amount of hot water you’re getting but also the quality of your water. Pay attention to any unusual noises your water heater makes, as this could be an indication that there’s a lot of sediment inside.

If your water heater appears rusty, it may be time to replace it . Remember that the average lifespan of most water heaters is around 10 years so if it’s older, it could just be time to purchase a new one.

A Tripped Breaker

If you have no hot water but your water heater seems fine, it could be the result of a tripped breaker. If your water heater has a switch that may have been turned off suddenly, check the corresponding circuit breaker.

The switch on your water heater could turn off all by itself if the breaker is tripped. Check your electrical panel and look for the breaker assigned to your water heater.

If the breaker is not in line with the other ones, it was probably tripped. All you need to do is flip the breaker to the off position, and then back to the on position. This simple flip of a switch should reset the breaker.

Once you reset the breaker, your hot water should work again. If the breaker continues to trip, it’s time to seek the help of a professional electrician. Your water heater should be on a dedicated circuit and if it’s not, you’ll need to let the pros fix the problem.

Don’t Panic if You Have No Hot Water

If you discover that you have no hot water, there’s no need to worry. The problem is usually caused by something simple that you can correct on your own.

Remember to check the pilot light on your gas water heater and take a closer look at the circuit breaker. A regularly scheduled flush can remove buildup to help your water heater run more efficiently.

If you need professional help with your hot water situation or you have other plumbing issues, make sure you visit our website and contact us today to schedule an appointment or to request a quote.

The post Help! I Have No Hot Water! appeared first on Aspen Plumbing and Rooter .

5 Essential Tips for Diagnosing Water Faucet Problems

Tue, 24 Sep 2019 19:27:00 GMT

A home with one faucet that leaks one drip per minute already wastes 34 gallons of water every year. Make that a leak rate of one drip per second, and in one year, it would’ve wasted almost 2,100 gallons of water! Now, consider that an average shower uses 17.2 gallons of water. That means you could have taken […] The post 5 Essential Tips for Diagnosing Water Faucet Problems appeared first on Aspen Plumbing and Rooter.

Now, consider that an average shower uses 17.2 gallons of water . That means you could have taken more than 120 showers with all that wasted water!

That’s said, you should never delay fixing water faucet problems. The earlier you detect these issues, the sooner you can fix them and keep them from turning into giant leaks.

Leaks aren’t your only faucet enemy though, as there is a multitude of issues that can affect them. Don’t worry though, as that’s exactly what we’re here to help you prevent. Keep reading to learn how to detect, diagnose, and possibly correct these problems!

1. Determining Water Faucet Leaks

One of the surefire signs you have a leak is an unexplainable increase in your water bills. Granted, Gilbert, AZ has had an increase in water rates back in 2018. But if your latest water bill is too high and there wasn’t any change in your water use, that’s a sign of water leaks.

The thing is, a leaky faucet isn’t always obvious, as the leak may be at the fixture’s base and not the spout. This is harder to notice since such leaks usually occur only when the faucet is running. It’s even more difficult to detect if the leak is at the faucet’s supply line, which is usually under the sink.

To check for a potential leak, have everyone at home stop using the water first. No faucets or toilet flush tanks should be running. Then, check your water meter — the pin or dial should be steady and not moving.

Most meters are outside of homes, near the curb by the front of a property. If you can’t find it there, it may be in the basement or near the water heater tank, somewhere close to the main water valve.

If the water meter is still running, take that as a sign you have a water leak. The next step is to determine which exact faucet is leaking.

2. Faucet Leaks You May Be Able to Repair on Your Own

Start by drying each faucet and the surrounding area and then running each of them, one at a time, for about a minute. Stop the flow and check the very base of the fixture — where the faucet body attaches to the sink. Water pooling there means that the leak is at the base of the faucet.

In this case, you may only have to replace the faucet’s damaged or dried-up O-ring. This part serves as a seal, so if it’s old or worn out, it lets water seep out of it.

If the sink is dry after the leak test, check and feel the supply line under it — if possible. If it’s damp or wet, or if the floor right under it has drops of water, then the leak is at the supply line. If you can easily access the supply line, tighten the fittings with a wrench.

Be careful though, as the supply tube is quite soft that you may end up puncturing it. If you’re not keen on doing this DIY task, consider hiring a local plumbing expert to carry out the faucet repair.

3. Dealing with Weak Water Flow or Low Water Pressure

Lack of water pressure or weak flow is a common side effect of hard water, the kind of water supplied to 90% of U.S. homes . The minerals in hard water can settle in and around faucet bodies and spouts. The sediments can harden inside the faucets and partially block the water’s path.

One of the easiest water faucet tips for weak flows is to soak the spout in a bag filled with water and vinegar. Let it sit overnight so that the vinegar’s acid can disintegrate the mineral buildup. You should also consider installing a water softener to prevent future sediment build-up.

4. Getting Rid of Noises from Faulty Faucets

Is one of your faucets making a screeching sound every time you run it? If so, then that’s a sign of a worn, hardened, or frayed rubber washer. The sound occurs as the water passes over the washer and tries to escape the seal.

Luckily, replacement washers are inexpensive and available in most hardware stores. You do have to disassemble the faucet though, so it requires a bit of faucet knowledge and DIY skills.

If what you’re hearing is more of a clicking or clanking sound, that may signal a broken-off faucet piece. Especially if you only hear the sound when running the water. In this case, a piece of metal may have chipped off and is banging against the sides of the faucet due to the flow of water.

While the noise itself may be a minor issue, the fact that the faucet broke means it won’t last that much longer. It would be best to get a replacement ASAP.

5. Faucet Handle is Super Hard to Turn or Operate

In many cases, this is again due to sediment build-up that may have caked the faucet’s cartridge. Old age may have also damaged its internal parts, preventing you from turning the handle.

If the fixture doesn’t appear to have cracks, use the vinegar and water faucet repair trick first. If this doesn’t work, try putting some silicone-based lubricant around the handle. If neither solves the problem, you may already need a faucet replacement.

Don’t Let Faucet Problems Stress You Out

As you can see, some water faucet problems are easy to solve, while others need professional help. What’s important is to ensure you get these issues fixed ASAP, otherwise, you may end up with huge water leaks. From there, they can get big enough to cause indoor flooding and water damage.

If you’re dealing with multiple faucet issues, please don’t hesitate to connect with us now . We can determine which exact faucets are giving you headaches, and from there, fix them right on the spot.

The post 5 Essential Tips for Diagnosing Water Faucet Problems appeared first on Aspen Plumbing and Rooter .

7 Common Plumbing Problems and How to Prevent Them

Thu, 12 Sep 2019 19:21:00 GMT

If you’re like most homeowners, you don’t like having to spend more money than you have to on plumbing services. Some homeowners avoid calling in a professional by ignoring the problem, but that can end up costing even more in the long run as many plumbing problems can cause water damage and allow mold to develop. […] The post 7 Common Plumbing Problems and How to Prevent Them appeared first on Aspen Plumbing and Rooter.

If you’re like most homeowners, you don’t like having to spend more money than you have to on plumbing services .

Some homeowners avoid calling in a professional by ignoring the problem, but that can end up costing even more in the long run as many plumbing problems can cause water damage and allow mold to develop.

Fortunately, there are a number of things you can do when encountering the most common plumbing problems that will allow you to only call a plumber when necessary.

Keep reading to learn more about what you can do to keep plumbing problems at bay.

1. Clogged Drains

Clogged drains are one of the most common plumbing problems faced by homeowners. Blockages may be made up of food, hair, or foreign objects such as toys. These can sometimes be removed with chemicals, a plunger, or a snake.

In this case, prevention is easier than dealing with the problem. You should ensure that all of your drains have guards. These are cheap and easy-to-find at your local hardware store.

Keep your drain guards cleaned out and they will prevent a myriad of things from getting into your drains which can cause them to become clogged.

2. Slow Drains

Sometimes, a drain still works but it takes far longer for the water to vanish than normal. In most cases, this is caused by a blockage that is still allowing some water to pass through the drain.

If not taken care of, a slow drain can evolve into a completely clogged drain which is why it’s important to act quickly when you notice your sinks or tubs aren’t draining like usual.

This is another easy plumbing problem to prevent with drain guards. However, these don’t keep grease and soap from getting into the drains which can slow things down.

To break up potential clogs, regularly pour hot but not quite boiling water down your drains. You can also pour a mixture of vinegar and baking soda followed by a lot of water to flush out small clogs before they become big ones.

3. Dripping Faucet

A single leaky faucet can waste up to 10 gallons of water every day. This costs you money and is harmful to the environment. Although in some cases this will require replacing the entire faucet, many times it’s a far simpler job that you can do yourself.

As long as you have the right tools, you can shut off the water to the sink and then pull it apart. Look for a washer that’s worn out, torn, or not sealing properly. Replace or adjust it before putting the faucet back together.

This is a problem that will likely come back eventually since things wear out over time, but you can put it off for longer by using high-quality washers that fit your faucets well.

4. Toilet Running

Most people have had to deal with a running toilet at some point. Although a jiggle to the handle can often solve the problem in the short-term, there are other steps you can take to more permanently resolve this issue.

Because a running toilet wastes even more water than a dripping faucet, it’s essential to get this fixed as quickly as possible.

In most cases, a toilet runs because the flapper is not properly closing. This is the rubber stopper that opens when you flush the toilet and then closes to allow the tank to fill up again.

When the toilet is running, open the tank and check the status of the flapper. Is it tangled in the chain that connects it to the handle? Is the chain too short and not allowing it to close? Is it worn out and not sealing properly?

Once you identify the problem, you can replace or adjust parts as needed and it should prevent you from literally flushing money down the toilet.

5. No Hot Water

Few things feel better than a steamy hot shower on a cold day. But, what do you do when that water never gets that warm or suddenly goes cold even though nothing else is using that water?

When there’s a problem with your hot water heater, don’t panic or call a plumber quite yet. It may be a simple fix that you can do yourself. There are two things that you want to check.

The first thing to look at is the pilot light. Relight it and then check back often to ensure it stays lit. If it doesn’t, you may need to clean or adjust the thermocouple to get it working again.

You also want to think about the last time you drained and cleaned out the tank. Over time, sediment can build up inside the hot water tank which can prevent it from heating properly or staying hot.

Flushing your hot water tank every year is a great way to prevent the hot water from going out and from needing more costly repairs done on your water heater.

6. Leaking Pipes

This is one of the most serious problems you can face. Leaking pipes can cause dampness throughout your home which can lead to mold growth . Mold is a health hazard and can cause damage to the structure of your home.

Although there’s not much you can do besides calling a plumber if you’re already dealing with this issue, there are some things you can do to prevent this problem in the first place.

The most common cause of leaking pipes is freezing temperatures that can cause the pipes to crack and burst. Although this isn’t as big of an issue in Arizona as it is further north, it can still happen.

When faced with freezing temperatures, allow your water to run at a trickle, especially when coming from outside sources. Running water can’t freeze and will prevent your pipes from doing so, too.

7. Sewage Backup

Another serious plumbing problem that some homeowners unfortunately face is a sewage backup. This can cause water damage to your home and is a serious health and environmental hazard.

The main thing you can do to avoid this problem is to prevent slow or clogged drains, so be sure to re-read those sections above for more information on how to prevent these issues.

If all of the drains in your home are running slow, call a professional plumber because this could indicate a sewage problem that needs to be addressed immediately.

You should also be aware of where your sewer lines are and avoid planting trees and other deep-rooted plants above them as these can damage the lines as they grow.

Need Help with One of These Common Plumbing Problems?

Now you know seven of the most common plumbing problems and what you can do to prevent them. These can help you save money and protect your home from water damage and mold.

If you are dealing with one of these problems and can no longer deal with it on your own, schedule an appointment with us . One of our experienced plumbers will come out and let you know how we can resolve your problem quickly and effectively.

The post 7 Common Plumbing Problems and How to Prevent Them appeared first on Aspen Plumbing and Rooter .

7 Benefits Of Using Water Softener At Home

Mon, 24 Jun 2019 11:05:00 GMT

If you are thinking to install a water softening system at your home, stop thinking and do it right now! Water softeners have very good benefits. To understand better, here are a few things you will get after a water softening service: Reduced electricity bill Any pipes and appliances that use water to function, such […] The post 7 Benefits Of Using Water Softener At Home appeared first on Aspen Plumbing and Rooter.

If you are thinking to install a water softening system at your home, stop thinking and do it right now! Water softeners have very good benefits. To understand better, here are a few things you will get after a water softening service:

Reduced electricity bill

Any pipes and appliances that use water to function, such as a dishwasher or coffee pot, work even more efficiently with a water softener . There is no limescale, which means there is no interference with heat transfer or clogged pipes . If the water heater uses soft water instead of hard water , 22%-29% less energy is consumed.

2-Increased life of pipes and appliances

When limescale gets developed on pipe, galvanic corrosion occurs. This type of corrosion damages the surface of anything that is even slightly conductive to electricity. Therefore the life of the pipe reduces and you need to buy new expensive pipes. There are ions in hard water that form soap scum which is an insoluble salt. The marks it leaves can be removed by some hard scrubbing. Such hard scrub can leave marks on your item and damage it.

3-Reduced need for soap with the water softener

Hard water reduces the lather in soap or shampoo, therefore you need to use more of the soap or shampoo. When you use a water softener, the use of these products reduces by 70% to 75%. You can get a lot of lather from a lesser amount of soap.

4-Soft and bright fabric

Minerals found in hard water get trapped in the fabric particles. This can make your clothes look stiff and dull. You can keep your clothes look new and bright for a longer time by using soft water.

5-Watering plants become easier

No one ever wants to use chlorinated water on plants. What some people do is they let water sit in a container for at least half an hour. This helps to drift out any chlorine from water. Then this water is used for watering plants. Whereas if you use a water softener, you can use the water straight from the tap to water your plants.

6-The life of your sewer system increases

If limescale settles in your pipe, it can reduce the diameter of your pipe by creating an extra layer inside. Thus water pressure increases and it may damage your sewer system . Water softeners can save you with this problem.

7- Better health

According to H.H. Mitchell, our brain and heart are composed of 73% water. Now you can think about how much water is essential for our body and if this water comes into the hard water form then health problems will start. A healthy life does not only comes with exercise and taking healthy foods but also drinking adequate amounts of water and if we don’t stop drinking Hard water then it can be dangerous for your health in the long run.

Do you know that excessive intake of calcium and magnesium can promote the stone build up in the body? Calcium can cause an overgrowth of bone joints if we take in an excess amount of hard water for a long time. It can also result in rough throat and may change the white color of your teeth into yellow color.

Use soften water only and drink water as much as possible because it has a moderate level of calcium and magnesium and this ability makes it good for your heart health, keeps your skin smooth and environment-friendly.

The post 7 Benefits Of Using Water Softener At Home appeared first on Aspen Plumbing and Rooter .

Why are Reverse Osmosis Systems so popular

Mon, 17 Jun 2019 11:22:00 GMT

Today Reverse osmosis systems have become a great choice and are highly in demand. It is one of the perfect choices for a water filtration system. But before you buy one for your home, you must know what does this actually mean. What is Reverse osmosis systems? RO is the process of producing water that […] The post Why are Reverse Osmosis Systems so popular appeared first on Aspen Plumbing and Rooter.

What is Reverse osmosis systems?

RO is the process of producing water that is free from any minerals or ions. This is achieved when the water is pushed with pressure along a semipermeable RO Membrane.

In the process of Osmosis, molecules of a solvent are passed from a less concentrated solution into a more concentrated one through a semipermeable membrane. To be more simple in words, it is the migration of a weak saline solution to a high saline solution. This is similar to how the roots of a plant take up water from the soil.

Semipermeable membrane

A semipermeable membrane will allow some molecules or atoms to pass through it with the help of diffusion. For example, let us consider a screen door. It allows tiny particles such as air molecules to pass from it, but bigger insects can pass through it. As another example, we can take a Goretex synthetic fabric . The fabric contains a very fine film of plastic in which millions and billions of tiny pores are cut. These pores are big enough to allow water vapor to pass through it but small enough to allow water through them.

What are the benefits of having a reverse osmosis system?

A better taste of water

Reverse osmosis system removes any contaminants such as salt, particles, colloids, and others. When you install a reverse osmosis system at your home, you get water that tastes good and smells good as well.

Water free from contaminants

Reverse osmosis systems are capable of removing any contaminants from water such as pesticides, nitrates, fluoride, bacteria, sulfates, arsenic, pharmaceuticals, and others of similar way. If you have an RO system that has a carbon filter, then you get water that is free from chloramines and chlorine as well.

It is easy to maintain RO systems

There are very few moveable and replaceable parts in a reverse osmosis system for water filtration. This makes the cleaning and repair service of an RO system very smooth and hassle-free. Also, if proper care is taken of your RO system such as cleaning at regular intervals and changing filters, your RO system will last long. If maintained properly, your reverse osmosis system can last for as long as 15 years.

Save money

Now you do not have to invest a heavy sum of money in water delivery services to get safe drinking water. Install RO systems at your home and save money!

The post Why are Reverse Osmosis Systems so popular appeared first on Aspen Plumbing and Rooter .

DIY Drain Cleaning and Why to avoid it

Sat, 18 May 2019 16:28:00 GMT

It can happen with anyone that you turn on the sink water and instead of going down the drain. It starts pushing up. You rely on many liquid drain cleaners you see in TV commercials but does it really work the way you think? Those companies that sell drain cleaners will never tell you that […] The post DIY Drain Cleaning and Why to avoid it appeared first on Aspen Plumbing and Rooter.

Those companies that sell drain cleaners will never tell you that the chemicals in it are very harmful to your drain pipe. All it “safe on pipes” claims are never completely true. If you want to use liquid drain cleaners to clean up small clogs, try to choose a natural enzymatic product. Natural enzymes will easily break up any organic material and bacteria that are clogged in your pipe. But these are good only for small clogs, they won’t remove any tough clogs.

You can use the products as monthly drain cleaning and maintenance. For regular drain cleaning, we have some easy DIY solutions that will help you more than an expensive product.

DIY solutions for drain cleaning

Hot Water: Take a big pot of extremely hot water (make sure it is not boiling water) and pour it in the drain which you want to clean or unclog. After it, pour down some cool water to flush away the melted clog.

Vinegar and baking soda: Pour half cup of baking soda in the drain and follow it with a half cup of vinegar. Let it be there for at least a night. Pour hot water later on and flush the drain in the morning. You should do it at least once a month.

How to remove tough clogs

The best tools to clean up tough clogs are an auger or a drain snake as well as a cup plunger.

Snake or auger is a tool that will help to break up any drain clogs. You enter the snake’s thick wire in the drain pipe and turn its handle. This will prevent the wire from spinning in the pipe. As the auger hooks to the clog, you can pull the wire out and remove the mess.

A cup plunger is best for small clogs. First, pull out the sink stopper and see if the clogging problem resolves with this. If not, seal the overflowing sink opening to create a proper suction needed to plunge. Put the plunger completely over the drain and pour little water in the sink. Start plunging up and down. You will feel when the clog has loosened up as the plunger will become easier to plunge.

Drain Cleaning Experts in Arizona

It is important to have the contact number of a reliable drain cleaning company saved in your contact list when the situation goes out of your hand. DIY can help you with small drain cleaning issues, bigger problems require the help of an expert drain cleaning company.

Aspen Plumbing and Rooters have more than 50 years of experience in plumbing services. We hire only trained, background-checked plumbers technicians. We also give emergency services for urgent plumber issues. Our customers get a 2-year guarantee on all repair work and installations. Call us at 480.648.0508 to book your drain cleaning service appointment.

The post DIY Drain Cleaning and Why to avoid it appeared first on Aspen Plumbing and Rooter .

Importance of Hiring a Licensed Plumber

Fri, 05 Apr 2019 12:08:00 GMT

Americans have the habit of practicing strange double standards. When it comes to buying bathroom fittings, they will always choose the best available and high-end brand. And when they have to get installation services, they will choose just any random local plumber from the street corner. You might save some money by this, but the level […] The post Importance of Hiring a Licensed Plumber appeared first on Aspen Plumbing and Rooter.

You might save some money by this, but the level and quality of work a licensed plumbing company will give you, nobody else might be able to. You might even face improper installation issue in the long run with an unlicensed plumber.

A plumbing job might look like an easy job, but it needs some great skills and hard work. Thorough knowledge of tools and techniques is required along with the knowledge of basic plumbing such as drain lines, water lines, sewer and gas lines. You should have proper knowledge of maths and mechanics to fit the right parts at the right place. A local plumbing company must also have the required skills to work at odd locations and tight times and schedules.

It is because of these reasons that it requires great training and years to become a licensed plumber. Some states might also need some extra basic courses before holding the license test. Basic continuous education is given by some states so that the professionals may stay updated on building codes, equipment upgrades, and safety issues.

Insurance

In order to maintain a valid license for plumbing services, one must qualify and get a license issued for yourself. The plumber’s license is liable for any damages that are made during the plumbing work at the client’s home. Therefore the customers have the privilege to file a claim for any damage made by a plumber during the work. This claim does not hold valid for any unlicensed plumber. You do not get any money back or refund for hiring an unlicensed plumber. Whereas, some states have recovery funds that do consider your claims if you had your plumbing service done by a licensed plumbing company or plumbing company.

Also, if you are a plumbing company with a license, you get full cover for any job-related injuries under your company insurance.

Plumber Background check

In order to qualify a license test, a local plumbing business has to pass some background checks such as a criminal background check. This is a very important point to consider because you can be tension free with a licensed plumber near you.

You can also do it on your own. When a plumber comes to your home for local plumber service, ask him for a copy of his license, and call the number of the licensing board to verify it. Ask for and contact the references if you are looking to consider this plumber for a high-end big project. Reach out to platforms such as the Better Business Bureau to see if there are any outstanding complaints regarding the plumbing company or plumber.

Why should you chose Aspen Plumbing

Giving a family-friendly plumber service is one of our top priorities. Our plumbers will clean up any mess made during the task before leaving your home. You can contact us at 480.648.0508 to schedule a local plumbing company. You can also to schedule a plumber visit, you can also fill out the form at the contact page .

The post Importance of Hiring a Licensed Plumber appeared first on Aspen Plumbing and Rooter .

How to be prepared for a plumber visit- Tips

Mon, 04 Mar 2019 11:07:00 GMT

Even if you are an expert in fixing all your plumbing issues at your home or business place, there comes a plumbing issue that can not be handled on your own. You would require a qualified plumbing maintenance service. If you feel any pipe repair is too much to handle on your own, contact a […] The post How to be prepared for a plumber visit- Tips appeared first on Aspen Plumbing and Rooter.

Even if you are an expert in fixing all your plumbing issues at your home or business place, there comes a plumbing issue that can not be handled on your own. You would require a qualified plumbing maintenance service . If you feel any pipe repair is too much to handle on your own, contact a plumbing emergency company immediately.

You must prepare your self for the plumber visit so that you can efficiently meet any urgent requirement on time. The guide here will help you to get the most benefit out of your plumber visit by helping you to be prepared beforehand:

Look for any other plumbing issue

Look for any other plumbing issues throughout the house. If you find any plumbing problem, let your technician know. It might be possible that one water line problem can be related to another and thus both can be fixed at one time. Thus you can efficiently save your time and money.

Contact a qualified plumber

You can not just choose any random plumber from your street corner who does little water pipe repairs. In order to get the best results, you must trust only a certified and experienced plumbing repair service. When you contact a plumber, ask him if he has any qualifications or certifications in the field.

Clear the area

Remove any unwanted item or obstacle from the area that needs the plumbing repair. This will help the plumber to work with maximum efficiency. The technician might need access to the main water line, and thus do not forget to clear it as well. This will make sure that the technician is able to finish his work quickly and smoothly and any damage to your property will be prevented.

Keep your pets away

Keep your pets in a separate room or area. Pets might distract the plumber from his work and that might delay the water line repair. This will also ensure the safety of your pets from any sharp tools or equipment.

Know the location of your plumbing

Get prior knowledge of where is the main plumbing of your home located, like a water heater, water pipe, main water line and more. This will help the plumber to fix your problem quickly without having to waste time to find which connection is where.

Aspen Plumbing is a plumbing repair company in Gilbert, Arizona. Our wide range of services includes drain cleaning, plumbing repair, water heater repair and installation, gas leak repair and installation and more. We believe in proving our customer loyalty by doing our work right at the first attempt with our experience of more than 50 years. We give a 2 years warranty on all the plumbing maintenance. Call our professional plumbers and get long-lasting plumbing solutions for the home maintenance.

The post How to be prepared for a plumber visit- Tips appeared first on Aspen Plumbing and Rooter .